Railway Sleeper Fixings: Screws, Brackets & Ground Spikes

Choose railway sleeper fixings for the connection you need to make. Joining two sleepers together, securing garden edging in suitable ground and anchoring timber into a new concrete foundation are different jobs.

Fixings Direct supplies timber and landscaping screws alongside sleeper brackets and garden hardware. This guide compares the main options and the measurements to check before choosing your pack.

Sleeper screws, brackets or anchors: where do you start?

Match the fixing type to the job
Connection Range to compare Main checks
Timber sleeper to timber sleeper Landscaping screws Timber thickness, screw length, head, drive and required penetration
Sleeper edging or a raised-bed layout in suitable ground Sleeper ground-spike brackets Straight or corner shape, ground conditions, layout and specified quantity
Timber connection to a new concrete foundation Concrete-in sleeper base anchor Foundation detail, anchor position and timber fixing arrangement

Joining the timber does not, by itself, establish the stability of the whole structure. Choose the ground support, base and fixing layout for the project as well.

Railway sleeper screws: hex head or wafer head?

Our TIMCO green hex head timber and landscaping screws use an external hex flange head with a fixed washer. The listed range is 6.7mm diameter, with lengths from 60 to 250mm and an 8mm socket drive.

Our TIMCO green wafer head landscaping screws have a broad, low-profile head and a TX recess. The 6.7mm screws use TX30; the 8.0mm screws use TX40. Diameters and pack quantities change across the available lengths.

Compare the head position, driver access and connection requirements. Both ranges are for timber-to-timber work; neither is a masonry anchor.

What length screw do you need for sleepers?

Measure the timber in the direction the screw will enter. Account for the first sleeper’s thickness, the required penetration into the second sleeper and the head position. Follow the fixing specification for the diameter, length and layout.

If you are comparing 150mm, 200mm and 300mm sleeper screws, check the diameter and drive along with the length. Our 300mm green wafer head option, for example, is 8.0mm diameter with a TX40 drive; it is a different size from the 6.7mm green hex head range.

Allow room for the driver and avoid placing fixings where they clash with another screw or bracket. Check pilot-hole requirements for the timber, particularly dense hardwood and positions close to edges or ends. A slash point does not remove every need to pre-drill.

Sleeper corner brackets and straight ground spikes

Our 430mm railway sleeper ground spikes have an upper fixing plate and a spike that is driven into suitable ground. The upper plate fastens to the reverse or inside face of the timber.

Choose the straight bracket for a straight run or the corner bracket for a 90-degree joint. These are separate options on the listing. The 430mm measurement is the overall bracket length, rather than the depth below ground.

430mm galvanised straight railway sleeper ground-spike bracket
Straight sleeper ground-spike bracket. The corner version has a different upper fixing shape.

Typical landscaping uses include raised beds, planters, steps and garden edging. Assess the ground and timber layout, check for buried services before driving spikes, and use the suitable timber fixings required by the installation detail.

Concrete-in sleeper base anchors

The concrete-in sleeper base anchor has an open angle bracket welded to a 220mm rod. Its bracket measures 100mm high × 75mm wide × 70mm deep.

The rod is cast into concrete. This is different from driving a ground spike into soil or bolting a surface-mounted bracket onto existing concrete. Position the anchor to the foundation detail and allow the concrete to reach the required condition before fixing the timber.

The 75mm bracket width is not a closed post-socket size. This sleeper base anchor is also not intended as a fence post support.

Outdoor finish and timber compatibility

Check the fixing material and finish against the sleeper species, treatment and exposure. The TIMCO green screw ranges have an exterior organic coating; the listed sleeper ground spikes are galvanised steel. The concrete-in anchor is a separate brown-coated product.

For oak or other hardwood sleepers, check material compatibility and drilling guidance for the chosen screw. A coating colour alone does not establish suitability for every timber or location.

How many sleeper fixings should you buy?

Count the specified connections and fixing positions before comparing packs. Screw boxes, bags, small packs and tubs can contain different quantities even where the screw length looks similar.

The 430mm ground-spike listing offers packs of 1, 10, 20 or 50 of the selected straight or corner style. The concrete-in base anchor offers packs of 1, 4 or 12. Check the selected option and whether any separate timber fixings are required.

What about sleeper retaining walls?

Retaining soil introduces loads that a simple edging layout may not have. The landscaping brackets discussed here do not establish a structural retaining-wall design or a permitted wall height. Use a suitable designed support arrangement for substantial retained soil or other loaded construction.

Once the connection is specified, compare our timber construction screws and sleeper and garden fixings. For help finding a listed size or pack, call Fixings Direct on 01278 551288.