Insulation Fixings: Which Type and Length Do I Need?

If you’re buying fixings for 100mm insulation board, start with what’s behind it. The same board can need a different anchor length on solid brick and lightweight aerated block. A roof deck is a different job again. Get the board thickness, backing material and installation detail in front of you before ordering.

At Fixings Direct, we carry plastic and metal insulation fixings, Ziel-Plast façade anchors, retaining washers and longer fixings for thicker board build-ups. Here’s where each one fits.

Which insulation board fixing do I need?

  • Ziel-Plast ETX-M insulation anchor and steel pin
    Ziel-Plast ETX-M steel-pin anchors. For holding external wall insulation boards to a suitable masonry wall. The hammered steel pin expands a sleeve in the wall and a 60mm head bears on the board. Use the 95–295mm size chart or shop the EM-coded ETX-M listings.
  • Ziel-Plast FIX-PA anchor and polyamide pin
    Ziel-Plast FIX-PA polyamide-pin anchors. The 10mm FIX-PA range also holds boards on a rendered masonry façade. A rigid plastic pin expands the sleeve. Choose 100–300mm by actual wall build-up and the embedment specified for the exact marked product.
  • TIMCO white plastic insulation fixing
    TIMCO white plastic insulation fixings. These one-piece 8mm hammer-ins retain insulation on suitable masonry. A 110mm PIF110 holds up to 70mm of total fixture thickness in TIMCO’s chart. Compare white TIMCO PIF packs and our other PIF pack listing.
  • TIMCO metal insulation fixing with retaining head
    TIMCO 8mm metal insulation fixings. An all-metal hammer-in fixing for retaining insulation on suitable masonry. A 170mm MIF170 has a 120mm maximum fixture thickness. Compare the 60–300mm range and the MIF-coded listing. Check exposure and board-system requirements before selecting a fixing for insulated plasterboard.
  • TIMCO galvanised slab nail
    TIMCO slab nails. Galvanised slab nails are driven into timber to secure insulation where the assembly calls for nails. Choose the length by the insulation build-up and required penetration into sound wood.
  • TIMCO helical flat-roof fixing
    TIMCO helical flat-roof fixings. Hammer-driven roof fixings are for specified plywood-faced composite insulation. Use the roof detail to choose a length. The 220mm, 250mm and 270mm options are covered below.

Which washers, retaining clips and accessories go with insulation fixings?

  • 35mm TIMCO metal insulation washer36mm TIMCO stainless steel insulation washer
    35mm and 36mm metal washers. Use a compatible screw to clamp insulation to battens when specified. Compare TIMCO 35mm metal washers and 36mm stainless steel washers. Check the centre hole and screw-head fit.
  • 85mm TIMCO large metal insulation retaining disc
    70mm and 85mm large metal retaining discs. Slide a large TIMCO disc over a compatible metal insulation fixing to spread pressure across softer boards. The MID70 has a 10mm hole and the 85mm MID80 has a 12mm hole.
  • TIMCO MID8240 oval stress plate
    82 × 40mm oval stress plate. The TIMCO MID8240 takes a compatible countersunk screw for fixing soft insulation to timber. The broad oval plate spreads pressure and seats into the insulation as specified.
  • Ziel-Plast TAD60 plastic insulation washer
    Ziel-Plast TAD60 plastic washer. Use a 60mm TAD60 with an appropriate 5–6mm screw into suitable timber, OSB or sheet metal. Also available as a separate TAD60 100-pack. Match the screw to the substrate.
  • Ziel-Plast TDW110 pressure washer
    Ziel-Plast TDW110 pressure washer. A 110mm retaining plate gives compatible anchors a larger bearing area on softer insulation such as mineral wool. See the TDW110-coded pack for the matching product.
  • Ziel-Plast 67mm insulation recess cutterZiel-Plast white EPS recess disc
    67mm cutter and white recess discs. The ZPFS cutter forms a shallow pocket in the board so the anchor head can sit below the surface. The ZB100 EPS disc fills that recess after the anchor is installed. Shop the 67mm cutter and 67 × 16.5mm white discs by size.
  • 65mm black cavity wall insulation retaining disc80mm red cavity wall insulation retaining disc
    Cavity wall insulation retaining clips. Clip the 65mm black disc, 80mm red disc or Fixings Direct 65mm clip onto a compatible wall tie to hold insulation against the inner leaf. The wider disc covers a larger area. The wall tie ties the two leaves together and is selected separately by the wall design.
  • Ziel-Plast SWT spiral insulation dowel
    Ziel-Plast SWT spiral dowels. Use a 6mm hex bit to screw a plastic SWT dowel into suitable EPS or mineral wool, then attach a lightweight item, such as a house number. Ziel-Plast recommends a 5 × 40mm screw. Select 50mm, 85mm or 125mm by usable insulation depth and the system detail. For securing the board itself, use the specified through-fixing.
  • TIMCO galvanised T50 staples
    Galvanised staples. Where a system calls for stapling a membrane or thin layer to timber, see TIMCO chisel-point staples. Match the staple to the tool and follow the membrane schedule. Rigid boards need their own fixings.

What size insulation fixing do I need for 100mm board?

For Ziel-Plast ETX-M installed flush, the manufacturer’s chart pairs 100mm insulation with 8 × 135mm on suitable concrete or standard masonry and 8 × 155mm on suitable aerated concrete. The latter needs 45mm of effective embedment, compared with 25mm in the listed concrete and masonry categories.

Our buying tip is to measure from where the fixing head will sit down to the sound wall. Old render and adhesive add to the distance the anchor must pass through. They don’t count as anchorage. If that build-up uses up the available allowance, check the next length in the full Ziel-Plast size chart. There are 11 lengths from 95mm to 295mm, all in boxes of 100.

How do I fit hammer-in external wall insulation fixings?

Mark the positions from your insulation system’s fixing schedule. Drill through the board into the supporting wall to the specified diameter and depth, using the drill mode for the actual substrate. Clear the hole, insert the sleeve and tap the pin home. The retaining head should sit flat against the board for a flush installation. A recessed installation uses the system’s specified cutter and plug.

For mineral wool, follow the specified washer diameter and fixing pattern. Check the pressure plate fits the anchor before ordering. Seat the fixing without crushing the slab.

220mm and longer fixings for thicker insulation boards

If you’re searching for 220mm insulation screws, check the substrate and fixing method first. For suitable flat roof systems, we carry TIMCO helical flat-roof fixings in 220mm, 250mm and 270mm. These are hammer-driven fixings for specified plywood-faced composite boards. TIMCO lists maximum fixture thicknesses of 185mm, 215mm and 235mm respectively for those sizes. Use the total fixture thickness and check the roof detail before ordering. For a system that specifies a screw, match the exact screw and plate to the timber or steel deck and the required thread engagement.

For a rendered masonry wall with thicker insulation, use the façade anchor chart instead. For example, Ziel-Plast’s 255mm ETX-M is listed for 220mm insulation in a flush application on suitable category A–D substrates. On aerated block, the same 220mm insulation points to the 275mm option. Check the actual build-up in both cases.

Do the new insulation regulations require 220mm fixings?

Approved Document L guidance for England sets out energy-performance guidance, including U-values for elements such as walls and roofs. The insulation specification comes from the design of the whole element. Once the board and build-up are specified, size the fixing for that assembly. There’s no blanket requirement for a 220mm board or fixing.

How many insulation fixings do I need?

Use the fixing schedule for your board and system. Façade corners and edges can need a different pattern from the middle of the wall, and wind exposure matters. Work out the total from the approved layout, then round up to complete packs.

Browse the Fixings Direct insulation fixings collection or see our TIMCO metal insulation fixing size guide for the full metal-fixing length chart.

Technical references: Ziel-Plast ETX-M technical sheet, TIMCO FIX-PA specifications and TIMCO flat-roof fixing range chart.